1

Teltonika FM1100

Тема: Teltonika FM1100

Dear Firends

We have a problem with FM1100 Ibutton readings,sometimes it just doesnt read ibutton .
It is working normally most of the times but suddenly doesnt respond and after some time works again .

Does anyone had same problem ?

2

Teltonika FM1100

Re: Teltonika FM1100

just be sure you configure correctly on the configurator

3

Teltonika FM1100

Re: Teltonika FM1100

aressun пишет:

just be sure you configure correctly on the configurator

What can be done wrongly?

Average constant =1
0
0
monitoring(or any other it doesnt matter)?

4

Teltonika FM1100

Re: Teltonika FM1100

I have a problem with FM11XX_Configurator_v1.1.6.3  That can't config my device.

popup error "device firmware not support " How I get device firmware for use with FM11XX_Configurator_v1.1.6.3 ??

or any way to do with my device ??

5

Teltonika FM1100

Re: Teltonika FM1100

Please read this section
Teltonika FM1100

Козлов Сергей
ООО "ГК"АТС-Мониторинг"
Регион: ПФО и не только...
http://www.atc52.ru
6

Teltonika FM1100

(04/10/2012 18:17:53 отредактировано ephedrine)

Re: Teltonika FM1100

-_-''  Thank for you reply but I can't read russia!!  :-(
I try google translate That to really BAD.

7

Teltonika FM1100

Re: Teltonika FM1100

I've sent you the latest firmware for your version of the configurator. Please check your e-mail.

Козлов Сергей
ООО "ГК"АТС-Мониторинг"
Регион: ПФО и не только...
http://www.atc52.ru
8

Teltonika FM1100

Re: Teltonika FM1100

I need to have a temperature sensor that is compatible with Teltonika FM1100. Any ideas ?

9

Teltonika FM1100

Re: Teltonika FM1100

Read manual?
Page 15:
1 – Wire devices
One of the realized features FM1100 is 1-Wire® dataprotocol, which enables
connection of thermometer (DS1820, DS18S20 and DS18B20)....

С уважением, команда Overseer.
Киев, Черкассы, Винница.
http://overseer.ua
10

Teltonika FM1100

Re: Teltonika FM1100

Hi dear Gurtam Partners,

did not want to write into the public area so here is a urgend problem we have with the FM11 devices:

We have mounted a Buzzer to DOUT2 and need the Firmware "29.01.01" which enables EVERY IBUTTON connected to the FM11 to have 0.5 Seconds DOUT1=1. (Buzzer will Peep for 0.5 Seconds).

Does anybody have this Firmware?

Or does anybody has a firmware which i can use for this?

Thanks
Wolf.
(wwbusch@gmail.com)

Politeness dictates it to write his name on a post
11

Teltonika FM1100

Re: Teltonika FM1100

Hi,

We have small problem configuration with the FM1100 .... and the I-Button

We configured the I button ...it works ...BUT it doesn't keep the settings ..as soon as we remove the button it send a ""zero""
I think we made a wrong setting ..

Who has a solution for us smile thanks in advanced

regards

""Baltika""

12

Teltonika FM1100

Re: Teltonika FM1100

Hello,

No wrong settings, it is FM1100 feature ;-)

At the settings you should set Reverse iButton and Deny empty iButton registration functions.
(because of these there won't be lines with empty ID=' ', so the driver stay logged in (binded) even there was only one iButton code when the iButton key was connected to the reader.

For unbinding you should make a Notification like this:
Digital input activation/deactivation > chose ignition's digital input & check for deactivation > Reset driver

With this method driver will be unbinded when the ignition is turned off.

Regards,

Krisztián

Eflotta Vehicle Tracking Ltd, Hungary
www.eflotta.com
13

Teltonika FM1100

Re: Teltonika FM1100

Hi Krisztián,

Thanks ...we will try smile I will keep you posted ..

regards

Baltika

Eflotta пишет:

Hello,

No wrong settings, it is FM1100 feature ;-)

At the settings you should set Reverse iButton and Deny empty iButton registration functions.
(because of these there won't be lines with empty ID=' ', so the driver stay logged in (binded) even there was only one iButton code when the iButton key was connected to the reader.

For unbinding you should make a Notification like this:
Digital input activation/deactivation > chose ignition's digital input & check for deactivation > Reset driver

With this method driver will be unbinded when the ignition is turned off.

Regards,

Krisztián

14

Teltonika FM1100

Re: Teltonika FM1100

I have discuss with  teltonika sell officer and he said

" basic FM1100 firmware does not have GPRS commands, you need a special firmware for that, goods can be acquired with it. What is the firmware version of units you have? I will check what kind of firmware it is and whether it supports GPRS commands. Each firmware has to have a matching configurator."

I want to know any one have gprs enable firmware and match configurator .  I just want to test  my device on my platform.

Ps. firmware version is version 12.xx.xx

15

Teltonika FM1100

Re: Teltonika FM1100

i dont think they have a fw they do the hardware/software configuration for some reason that is one of there flaws

16

Teltonika FM1100

Re: Teltonika FM1100

But I used a lot of teltonika from different supplier . Each supplier have they own firmware for those device.
I have some device come with online platform support and those device can recieve gprs command to cut engine / remote management .  firmware is version 12.xx.xx But I can't config device with other configulator . when I flash device with other firmware (1.xx.xx )  device not respond to command .

17

Teltonika FM1100

Re: Teltonika FM1100

If you are using a standard FM1100 it will accept GPRS based commands, you do not need any special changes. In Wialon you just need to mak sure that you set up commands for the units.

The command can only be sent if the unit has an active GPRS session.

I am having a firmware modification done to have 150 geozones stored on the device so we can set up a route and route management using only sms and to both the monitoring application and a mobile phone.

The current firmware version is FM11010720.e and the configurator is 1.1.7.15. This also has a fix for a GPS bug.

Regards
John

Phoenix Solusi
Mobile Visible Secure
Specialists in data acquisition and analysis for mobile and fixed assets. Integration in to content management systems is a specialty we have.
18

Teltonika FM1100

(26/04/2013 05:55:18 отредактировано ephedrine)

Re: Teltonika FM1100

I didn't use Fm1100 with wialon . I have my own platform .
And I want to send output activate command via gprs.
I try device with fw1.xx.xx is not work . but device with Fw 12.00.00 is work(I not have fw & match configulator) .

Teltonika FM1100

19

Teltonika FM1100

Re: Teltonika FM1100

Just sent you the latest files to your email. Try these.

Phoenix Solusi
Mobile Visible Secure
Specialists in data acquisition and analysis for mobile and fixed assets. Integration in to content management systems is a specialty we have.
20

Teltonika FM1100

Re: Teltonika FM1100

Thank you , very much

21

Teltonika FM1100

Re: Teltonika FM1100

Let me know if it works

Phoenix Solusi
Mobile Visible Secure
Specialists in data acquisition and analysis for mobile and fixed assets. Integration in to content management systems is a specialty we have.
22

Teltonika FM1100

Re: Teltonika FM1100

I didn't receive any email . what e-mail address you're send ?

please send to : info@smarttrack.in.th or use file hosting . I use gmail service it's block some file content .

23

Teltonika FM1100

Re: Teltonika FM1100

Guys,

Could you add me some examples about the sintax to send gprs commands?, I use a Teltonika FM5300 and I don't know if I have to put login/password, or APN Name/APN Pass for Gprs particular case. that's will be helpfull.

Jorge Baeza Osorio

24

Teltonika FM1100

Re: Teltonika FM1100

Hi Jorge,

Are you trying to send the commands from within Wialon?

Regards
John

Phoenix Solusi
Mobile Visible Secure
Specialists in data acquisition and analysis for mobile and fixed assets. Integration in to content management systems is a specialty we have.
25

Teltonika FM1100

Re: Teltonika FM1100

Hi Krisztián,

Is there a way to ""retranslate"" the reverse code what is send to Wialon into the code ""on the key"" ? ( retranslate by hand or tool )

regards

Baltika