1

Meitrack MVT380

Тема: Meitrack MVT380

how do i set tracking interval on the Wialon website using MVT380
and how do i send command for engine imobilization (engine start and stop) from the web software
any other experiences using MEI devices please share

2

Meitrack MVT380

Re: Meitrack MVT380

fahadakhaan,
tracking interval can be modified in MVT380 device settings, there is no direct feature in software.
But it's available to send a custom message to that tracker (in a proper format that can be found in MVT380 user guide).

Developer
Gurtam
3

Meitrack MVT380

Re: Meitrack MVT380

fahadakhaan пишет:

how do i set tracking interval on the Wialon website using MVT380
and how do i send command for engine imobilization (engine start and stop) from the web software
any other experiences using MEI devices please share

Supposedly you have to send a GPRS command customized -you can find them in the communication protocol, but they have never worked, at least in my case.

4

Meitrack MVT380

Re: Meitrack MVT380

globallbs
Please give us commands that you tried to send. Maybe you used wrong format

WDC Administrator
Gurtam
5

Meitrack MVT380

Re: Meitrack MVT380

I´m using the commands of the communication protocol:

A10: Track on demand
B33: Power Down Mode
C01: Output Control

Please tell me if I'm wrong.

Thanks.

6

Meitrack MVT380

Re: Meitrack MVT380

mvt380 means what ?

7

Meitrack MVT380

(22/08/2012 10:38:19 отредактировано cttmx)

Re: Meitrack MVT380

Please help me

I need to setup 200 devices their are Meitrack MVT380 with temperature sensor

in meitrack MS02 platform i need to put a formula (4700*ADC1)/(1024-ADC1)/1000 and choose a Tsensor_5k 

ADC1 = analog port where sensor is phisicaly connected to MVT380
Tsensor_5k  is a resistance but no phisicaly present

when i do, as wialon instructions: Temperature sensor, parameter = ADC1, i got a value for example: 3.26 when the real temperature is 22 celsius

somebody can help me ???

8

Meitrack MVT380

Re: Meitrack MVT380

hm, basicaly ADC value should be digital and not a voltage on Meitrack devices.
are you shure that you not already made some conversions?
ADC1 is a voltage counter, so you are mesuring the voltage of the temp sensor.
do you have a calculation table between voltage and temperature?

In Wialon you can enter very good the coresponding value table!

Wolf.

Politeness dictates it to write his name on a post
9

Meitrack MVT380

Re: Meitrack MVT380

I use Meitrack MVT380 and connect ADC1 with fuel level sensor.
And in platform I add sensor type as Fuel level sensor and metrics is lites .

how to make fuel level chart in report ?

10

Meitrack MVT380

Re: Meitrack MVT380

:-D  meitrack sensor is need power source to work.
may you use 10 K resister to separate 12 V  to 4 V @ sensor .
and tab adc line between 10K resister and sensor :-)

12Vdc -------xx10Kxx---------ADC---------5Ksensor---------Ground    <<  like this :-)

11

Meitrack MVT380

Re: Meitrack MVT380

wwbusch пишет:

hm, basicaly ADC value should be digital and not a voltage on Meitrack devices.
are you shure that you not already made some conversions?
ADC1 is a voltage counter, so you are mesuring the voltage of the temp sensor.
do you have a calculation table between voltage and temperature?

In Wialon you can enter very good the coresponding value table!

Wolf.

Yes you will need to add calculation table using the txt data values and ADC1 val.

--
Spread the AVL- World