1

Queclink GV200

Topic: Queclink GV200

Does anybody information about which Queclink gv100 & gv200 @track messages are supported by Wialon?

Thanks!
Tom

2

Queclink GV200

Re: Queclink GV200

GT SOS,  GTFRI may be the only supported

--
Spread the AVL- World
3

Queclink GV200

Re: Queclink GV200

tomalex
Any messages like FRI (TOW, ... etc.) + SOS.

4

Queclink GV200

Re: Queclink GV200

Does anybody knows correct AT command to enable SOS and Digital port 3 or 4 in order to activate a panic button over GV100 quectel?

5

Queclink GV200

Re: Queclink GV200

Hello,

i need to get the list of SMS commands to configure and setup my Quelink GV200 device to connect it on wialon.  any idea???

6

Queclink GV200

Re: Queclink GV200

Do you have the Manger tool for GV200 ? you can copy and paste from the Manger-tool and send via SMS , if otherwise let me know I can send you the commands.

Ysv
7

Queclink GV200

Re: Queclink GV200

Hello,

no i do not have the tool, i just need commands to send to setup the device and connect it to WIALON server under my account, thanks in advance for help

8

Queclink GV200

Re: Queclink GV200

01. Quick Start settings -

AT+GTQSS=gv200,apnname,user,password,3,,2,193.193.165.165,20420,0.0.0.0,0,,60,0,0,,FFFF$

(Replace-  apnname,user,password with your ISP settings)


02.Global Config.

AT+GTCFG=gv200,gv200,gv200,1,0,0,,3F,2,,3FFF,0,0,0,300,0,1,0,0,1F,0,FFFF$

(with power saving when Ignition is off)


03.Reporting

AT+GTFRI=gv200,1,0,,0,0000,0000,,5,1000,1000,,15,600,0,,,,FFFF$

(Fixed time , 5 seconds update)


+ Above should get your Gv200 connected to the Wialon server  , if does not work , please change the IP of the 1st command to 193.193.165.167 and check on id.wialon.net  if the device IMMIE reflects on the page .

+ Im using GV200's default password in these commands  , if you have changed it please replace 'gv200' with the password you've set.

+  If you have any sensors connected you will have to configure them with more commands.


+ If you write to Qucelink  , they will send you the manger tool , You need to have the correct UART cable to configure the device using your computer.

update the ticket if you were able to get the device connected .

Ysv
9

Queclink GV200

Re: Queclink GV200

Thank you so much.

but my APN doesn't have username or password, do i replace it with space or what?

what is the commands to reset all current configuration on the GV200 device?

10

Queclink GV200

Re: Queclink GV200

just leave them blank ( no space) , like below .

AT+GTQSS=gv200,apnname,,,3,,2,193.193.165.165,20420,0.0.0.0,0,,60,0,0,,FFFF$


Not sure how to re-set the password , you might have to write to queclink.

Ysv
11

Queclink GV200

Re: Queclink GV200

Thanks for your reply,

but i need to reset all the device not only password.  any idea?

12

Queclink GV200

Re: Queclink GV200

do you have the password ?if you dont have the password ,
email support@qucelink.com they will help you out.

Ysv
13

Queclink GV200

Re: Queclink GV200

i have no details at all , i sent  email now and hope they will reply .

thanks for your support smile

14

Queclink GV200

Re: Queclink GV200

Why dont you insert a sim and send the comands with default password . It might work.

Ysv
15

Queclink GV200

Re: Queclink GV200

Hi ,

I checked with Queclink for you , What they said was that you can flash the firmware again to reset the password. You require an UART cable to do it .

@wwbusch aka Buwo thank you for liking and adding Karma to my profile smile

Ysv
16

Queclink GV200

Re: Queclink GV200

good to know that reflashing the FW helps.
On ATrack HW even that does not help.

Wolf.

Politeness dictates it to write his name on a post
17

Queclink GV200

Re: Queclink GV200

You are right , atrack has  a unique reset ID for each individual unit which you have to obtain from atrack itself.

Ysv
18

Queclink GV200

Re: Queclink GV200

buen día colegas

alguno tiene un manual de configuración via SMS para estos equipos

Lps Trackers
19

Queclink GV200

Re: Queclink GV200

lpscolombia, GV200 supported by flespi. Try this guide to setup connectivity: https://flespi.com/blog/configuring-que … ith-flespi

Follow us on http://www.facebook.com/Gurtam
And take a look at new IoT backend by Gurtam.